| Bike Shops and Bicycle Repair Shops | |
|
Listings
of Bike Shops and Bicycle Repair Shops California Bike Shops * Bicycle Sales and Repair Shops in California, listed by names of cities Alameda, California * Castro Valley, California * Los Angeles, California * Oakland, California * Palo Alto, California * Sacramento, California * San Diego, California * San Francisco, California * San Jose, California * San Mateo, California * Walnut Creek, California Bike Shops and Bicycle Repair Shops in Other States Boulder, Colorado * Chicago, Illinois * Dallas, Texas * Jacksonville, Florida * Memphis, Tennessee * New York, New York * Portland, Oregon * Seattle, Washington Bicycle Shops and Bike Repair Shops in Other Countries Brisbane, Australia * Sydney, Australia * Hampshire, England * Sale of Bicycles, Parts and Accessories for all types of terrains, repairs and add-ons |
Tires can be tightly fitted to the rim. Use tire levers to pry tire bead up and over rim sidewall. Do not use a screwdriver, knife, or other sharp object, which might damage tire or tube. Fully threaded valve shafts may have a locking nut next to rim. Loosen and remove locking nut before deflating.
Deflate tire completely. Even a small amount of air left in the tube can make it more difficult to get the tire off. For best results, press downward on wheel while depressing the valve. Push one bead of tire toward rim center. The tire bead will be pressed tight against rim. Pushing it inwards loosens the bead from the rim. Repeat on other bead.
Engage one tire lever under bead of tire. Engage second lever 1-2" (25-50mm) from first lever then pull both levers toward spokes to lift bead off rim. Disengage one lever. Move it two inches (5cm) along the rim and engage lever in the bead. Pull lever to lift next section of bead off rim.
Repeat engaging the lever until the bead loosens. Then slide the lever along the rim under the bead.
Starting opposite the valve, pull inner tube from tire. Lift valve from valve hole and remove tube from wheel. Remove second bead from rim, which removes tire completely from rim. To fully inspect the tube and tire, it is best to remove both completely. Other tire lever options: Some tires remove easier with a thinner and wider lever such the TL-2
Some tire and rim combinations require a very strong steel lever, such as the TL-5
It is important to always inspect the tire as well as the inner tube. The cause of the flat, such as a nail or piece of glass may still be embedded in the tire or tread. Inspect both the outside of the rubber tread and the inside of the casing.
Inspect outside of tread for protruding nails, pieces of glass, thorns, or other objects. Squeeze any cut to look inside for objects such as slivers of glass. Visually inspect inside of tire casing for nails, glass or debris. Wipe inside of casing with a rag, and then carefully feel inside with fingers. Inspect sidewall for rips, holes, or damaged rubber and casing. Inspect wire or fabric tire bead for damage.
The wheel rim is made with holes between the rim sidewalls for spoke nipples. A rim strip covers the holes or nipples. The rim strip can be made out of different materials such as cloth, rubber, or polyurethane plastic. The strip protects the inner tube from sharp edges in the base of the rim and from spoke ends and nipples that might puncture the tube.
Inspect inside the rim cavity, looking at the rim strip and for any sharp corners or protruding spokes.
The rim strip should be wide enough to cover the bottom of the rim, but not so wide it interferes with the seating of the tire bead. Inspect the rim strip whenever changing a tire or inner tube. Look for tares and rips, and make sure rim strip is centered over the nipple holes. In the image below, the rim holes are exposed, which may cause a flat tire.
There are two common types of valve stems on bicycles, the schrader ("American" type) and the presta ("French" type). The schrader or American-type valve is common on cars and motorcycles. It is also found on many bicycles. The valve stem is approximately 8mm (5/16”) in diameter and has an internal spring plunger to assist in shutting the valve. To deflate the schrader valve tube, it is necessary to stick a small hex wrench or other object into the valve in order to press on the stem and release the air. Upon release of the stem, the stem spring shuts. Schrader compatible pump fittings press on the internal stem with a plunger, allowing the tube to be filled.
The schrader valve core can be removed if necessary. This is rarely required, but a valve can become stuck and cause a slow leak. A loose core can also be the source of a slow leak.
Bubble of soapy water showing a leak at valve
The presta or French-type valve is common on mid and higher priced road bikes and on higher priced MTB bikes. Presta stems are nominally 6mm (1/4”) diameter, thinner than Schrader valves. At the top of the stem is a small locknut, which must be unthreaded before air can enter the tube. To deflate the inner tube, unthread the locknut. Depress the valve stem to deflate. To inflate the tube, unthread the locknut and tap the valve to insure it is not stuck.
Tap valve to clear and release internal seal
Presta valve tubes come with different length valves. The longer valve stems are needed for the deeper aerodynamic rims.
The rim valve hole should match the valve of the tube. It is possible to use the smaller presta valve in a rim intended for the larger Schrader by using an adapter sleeve. Repairing an Inner Tube Simply replacing the punctured inner tube with a new tube is always the safest and most reliable procedure. However, it is possible in some cases to repair a small hole in an inner tube. If the hole is quite large, it may not be possible to repair. When in doubt replace the tube.
The GP-2 Super Patch Kit uses pre-glue patches. There is no tube of glue to leak or dry up. The VP-1 uses a vulcanizing fluid to bond the patch to the inner tube.
Simply replacing the punctured inner tube with a new tube is always the safest and most reliable procedure. However, it is possible in some cases to repair a small hole in an inner tube. If the hole is quite large, it may not be possible to repair. When in doubt replace the tube.
The GP-2 Super Patch Kit uses pre-glue patches. There is no tube of glue to leak or dry up. The VP-1 uses a vulcanizing fluid to bond the patch to the inner tube.
Note directional arrows of tire manufacturer, if any. Directional arrows printed on the sidewalls indicate rotation of wheel. Not all tires have direction orientation. Inflate tube enough for tube to just hold its shape. Install tube inside tire. Install with tube valve adjacent to air pressure recommendations written on tire sidewall. Lower tire and valve into rim valve hole and align valve so it is pointing straight toward hub. A crooked valve can lead to a flat tire later. Install one bead at a time. Work tire bead onto rim with hands. If tire bead will not seat using hand, use tire lever as a last resort. Use caution when using tire levers to avoid pinching inner tube. Engage tire lever using same orientation as removing bead.
Work tube over rim sidewall and into rim cavity. Install second bead onto rim. Use care if using a tire lever. Inspect both sides of tire for bead seating and for any sign of the inner tube sticking out. Re-install if necessary. Inflate to low pressure and inspect bead again on both sides. Look for small molding line above bead. This line should run consistently above rim.
Inflate to full pressure and check with pressure gauge. It may be necessary to press downward above the valve in order to engage the pump head. For fully threaded valve shafts, re-install the locking nut, if any. Do not use wrench or pliers to tighten nut. Tighten finger tight.